|
Applying
Colour Shield's PPS is very easy to do.
Depending
on the vehicle size, the entire application process can take as
little as one hour. Please see the following instructions for applying
Colour Shield.
Method
#1 - Manual Application
Wash
vehicle normally to remove all dirt.
Pour contents of Polarizing Wash Solution into 4 Litre's. of hot
water and then mix.
Wash painted/gel coated surfaces with the Polarizing Wash Solution.
Leave the Polarizing Wash Solution on the painted/gel coated surfaces
until hazy and dry.
Rinse and wipe off Polarizing Wash Solution from applied surfaces
until completely removed. Dry with a soft clean cloth or chamois.
(See the step one video)
Once
the painted/gel coated surfaces are completely dry, move vehicle,
boat, or aircraft to a shaded area.
Apply 2 small coin sized dabs of the Paint Protection Coating
to a new Foam
Applicator and apply to 1 sq meter section at the time in circular
motion and repeat this step until all said surfaces are covered.
Use
a clean cloth or terry
cloth to remove hazed Paint Protection Coating at the
point you began the application. (See the step two video
shows machine & manual application).
Note
- You can also apply a second coat on the horizontal surfaces such
as hood and roof. We raccomend usining a little masking tape on
the edge of black rubber or matted surfaces.
You're
done!
Method
#1A - Manual Application (Reduced Water)
Wash
vehicle normally to remove all dirt.
Pour Half of the Polarizing Wash Solution into 2 Litre's.
of hot water and then mix.
Wipe down the painted/gel coated surfaces with the Polarizing Wash
Solution.
Leave the Polarizing Wash Solution on the painted/gel coated surfaces
until hazy and dry.
Wash the surfaces with clean water and a clean sponge changing your
water a couple of times. Dry
with a soft clean cloth or chamois. (See the step one video)
Once
the painted/gel coated surfaces are completely dry, move vehicle,
boat, or aircraft to a shaded area.
Apply 2 small coin sized dabs of the Paint Protection Coating
to a new Foam
Applicator and apply to 1 sq meter section at the time in circular
motion and repeat this step until all said surfaces are covered.
Use
a clean cloth or terry
cloth to remove hazed Paint Protection Coating at the
point you began the application. (See the step two video
shows machine & manual application).
Note
- You can also apply a second coat on the horizontal surfaces such
as hood and roof. We raccomend usining a little masking tape on
the edge of black rubber or matted surfaces.
You're
done!
Method
#2 - Using Orbital Polisher/Buffer
Wash
vehicle normally to remove all dirt.
Pour contents of Polarizing Wash Solution into approximately 4 Litres.
of hot water then mix.
Wash painted/gel coated surfaces with the Polarizing Wash Solution.
Leave the Polarizing Wash Solution on the painted/gel coated surfaces
until hazy and dry.
Rinse and wipe off Polarizing Wash Solution from applied surfaces
until completely removed. Dry with a soft clean cloth or chamois.
(See the step one video)
Once
the painted/gel coated surfaces are completely dry, move vehicle,
boat, or aircraft to a shaded area.
Apply 2 small coin sized dabs of the Paint Protection Coating to
a new De-luxe Foam Applicator and apply to 1 sq meter section at
the time in circular motion and repeat this step until all said
surfaces are covered.
Buff
off vehicle with an Orbital Polisher and a finishing pad, use the
machine the lowest speed setting. (Approx. 1800 RPM). (See the step
two video).
Note
- You can also apply a second coat on the horizontal surfaces such
as hood and roof. We raccomend usining a little masking tape on
the edge of black rubber or matted surfaces.
You're
done!
Note:
The
step 1 video talks of paint contaminant removal, further product
information including a detailed video can be seen in the Paint
Cleaning Kit or by following this link.
|
